Bush-hog SM 60 Manuel d'utilisateur

OPERATIONll MAINTENANCE1007 $4.0097701Model SM 60Side Mount Rotary CutterOperator’s ManualBUSH HOG®

TABLE 1-1 SPECIFICATIONS(For Cast Iron Pump & Motor Only)MODEL NUMBERSM60R SM160RRequired PTO Speed 540 rpm 1000 rpmPump Output 21.4 gpm 19.1 gpmM

F. Pull driveline apart. Attach the outer (female)section to the tractor PTO shaft and the inner (male)section to the pump input shaft. Pull on eac

G. Repeat steps “E” and “F” to other driveline sec-tion.H. De-burr the ends of the drivelines and cleanaway all chips and filings. (Fig. 2-7)I. App

KEEP CLEAR OF MACHINE WHEN RAISING AND LOWERING THE CUTTER HEAD.D. Place cutter deck in desired working position.E. Engage PTO drive with tractor a

3-5 STORAGEA. Apply light coat of multi-purpose grease to slid-ing assemblies.B. Perform steps “A” through “G” in paragraph 3-4.C. Relieve hydraulic

EVERY 150 HOURS1. Cables - Wearing gloves, wipe cables with an oilsoaked rag.YEARLY1. Hydraulic Tank - Drain hydraulic tank while oil iswarm.Clean suc

4-4 BLADE HOLDER REMOVAL (Fig. 4-3)THE CUTTER CAN FALL FROM HYDRAULIC SYSTEM FAILURE. TO AVOID SERIOUS INJURY OR DEATH, SECURELY SUPPORT CUTTER BEF

D. Turn motor 180º. Reinstall bolts retaining motorto spindle housing.E. Reinstall hydraulic fittings, and hoses. Replacefitting O-rings as necessar

Table 4-4 General TroubleshootingTROUBLE PROBABLE CAUSE REMEDY1. Hydraulic Pump Noisy Cavitation Check condition of suction strainer and returnline fi

SECTION VASSEMBLYTHE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY.1. Wear personal protective equip

CONGRATULATIONS!You have invested in the best implement of its type on the market today.The care you give your Bush Hog implement will greatly determi

5-1 BASIC MACHINE ASSEMBLYBASE UNIT IS EXTREMELY TOP HEAVY WHEN DISCONNECTED FROM CUTTER DECK AND SHOULD BE MOVED ONLY BY CONNECTING TO TRACTOR

USE OF THIS MACHINE ON TOO SMALL A TRACTOR CAN CAUSE TRACTOR UPSET. DO NOT USE THIS MACHINE ON A TRACTOR WEIGHING LESS THAN 6000 LBS. (2722 kg), NOT

5-5 OPTIONAL TAILWHEELINSTALLATIONA. Position mounting bracket against underside offrame as shown. (Fig. 5-6)B. Position mounting plate on top si

SAFETY DECALSTo promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either

SAFETY DECALS CONTINUED218337383375826178337483377

B O L T D IA M E T E RW R E N C H (IN .) “ B ” A N D S A E S A E S A ES IZ E (IN .) “ A ” T H R E A D S IZ E G R A D E 2 G R A D E 5 G R A D E

P.O. Box 1039 llSelma, AL 36702-1039Telephone (334) 874-2700 ll www.bushhog.com

RETAIL CUSTOMER’S RESPONSIBILITYUNDER THE BUSH HOG WARRANTYIt is the Retail Customer and/or Operator’s responsibility to read the Operator’s Manual, t

LIMITED WARRANTYOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOBush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from anauthorized

DEALER PREPARATION CHECK LISTSM60 ROTARY CUTTERBEFORE DELIVERING MACHINE — The following check list should be completed.Use the Operator’s Manual as a

IMPORTANT SAFETY PRECAUTIONSThis symbol is used to call attention to safe-ty precautions that should be followed by the operator to avoid accidents. W

IMPORTANT SAFETY PRECAUTIONSThis symbol is used to call attention to safe-ty precautions that should be followed by the operator to avoid accidents. W

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGEMPLOYERS, EMPLOYEES AND OPERATIONS.*(This section is intended to explain in broad terms the concept

SECTION IINTRODUCTION AND DESCRIPTION1-1 INTRODUCTIONWe are pleased to have you as a Bush Hog cus-tomer. Your Side Mount Rotary Cutter, ModelSM60,ha